JIC FLARE ADAPTERS
All GS-JIC 37° flare fittings comply with SAEJ 514 (ISO 8434-2). In addition to basic JIC 37° flare fittings, GS-Hydro also delivers special JIC 37° flare fittings – either with or without an O-ring – which are type approved by Det Norske Veritas. GS-Hydro’s JIC-fittings are specified by NORSOK (specification classes FS70, IS70) to be used offshore.
Technical data
Carbon steel | AISI 316 | AISI 316 and carbon steel with o-ring | |||
---|---|---|---|---|---|
Tube OD, etc | Tube OD, inches | Max. pipe wall thickness, etc | Max. permissible working pressure, bar | Max. permissible working pressure, bar | Max. permissible working pressure, bar |
6 | 1/4 | 1.5 | 430 | 430 | 600 |
8 | 5/16 | 1.5 | 430 | 430 | 600 |
10 | 3/8 | 1.5 | 430 | 430 | 600 |
12 | 1/2 | 2.0 | 350 | 350 | 490 |
16 | 5/8 | 2.5 | 350 | 350 | 490 |
18 | 3/4 | 2.5 | 350 | 350 | 490 |
20 | – | 2.5 | 350 | 350 | 490 |
22 | 7/8 | 2.5 | 350 | 350 | 490 |
25 | 1 | 3.0 | 250 | 250 | 420 |
30 | – | 4.0 | 250 | 250 | 420 |
38 | 1 1/2 | 5.0 | 250 | 250 | 420 |
Note! The working pressure applies to the adapters, not the pipes! |
---|
Carbon steel and stainless steel (AISI 316) GS-JIC 37° flare fittings without an O-ring may (according to the type approval from DNV) be used for the following media:
- Freshwater
- Sea water
- Sanitary
- Compressed air
- Hydraulic
- Fuel oil (JIC to NPTF only)
- Lubricating oil (JIC to NPTF only)
- Steam and condensate
- Fire water
- Deluge systems
Carbon steel and stainless steel (AISI 316) GS-JIC 37° flare fittings with an O-ring may be used (according to the type approval from DNV) for the following media:
- Freshwater
- Sea water
- Sanitary
- Compressed air
- Hydraulic
- Steam and condensate
- Nitrogen
- Shield gas
- CO2
- Fire water
The following O-ring materials should be used:
- For gas media AFLAS 100H / 100S
- For other media Nitrile 70 shore
Carbon steel and stainless steel (AISI 316) JIC 37° flare fittings may be used for a wide range of applications including hydraulic, freshwater, fuel and lubricating oil among others. The maximum allowable working pressure of JIC 37° flare fittings (according to ISO 8434-2) are as follows:
JIC 37 ° flare fittings (according to ISO 8343-2) |
---|
Tube OD, etc | Tube OD, inches | Max. pipe wall thickness, etc | Max. permissible working pressure, bar |
---|---|---|---|
6 | 1/4 | 1.5 | 350 |
8 | 5/16 | 1.5 | 350 |
10 | 3/8 | 1.5 | 250 |
12 | 1/2 | 2.0 | 250 |
16 | 5/8 | 2.5 | 250 |
20 | – | 2.5 | 200 |
22 | 7/8 | 2.5 | 160 |
25 | 1 | 3 | 160 |
30 | – | 3 | 125 |
32 | 1 1/4 | 3 | 125 |
38 | 1 1/2 | 3 | 100 |
Category: JIC Flare Adapters